Country Guide: United States
In the United States, the tariff follows the specification.
Two sofas can leave the same factory in Bento Gonçalves on the same truck and land in Long Beach under different tariff regimes, because one has a wooden frame and the other does not. From 1 January 2027 the gap between them widens. This is what a buyer needs to know before a specification is signed.

Verified against primary sources on 6 November 2026. Tariff schedules change, and the 1 January 2027 increase has already been postponed once. Confirm every figure below against the source before you price against it.
01What is in force, and since when
A buyer who priced Brazil in 2025 was pricing against a 40 percent tariff that no longer exists. A buyer who priced it in the spring of 2026 was pricing against nothing. Both numbers were right at the time and both are wrong now, so the sequence matters.
On 20 February 2026 the Supreme Court held in Learning Resources, Inc. v. Trump that the International Emergency Economic Powers Act does not give the President authority to impose tariffs. Executive Order 14389 terminated every tariff resting on that authority the same day, and Customs and Border Protection stopped collecting them on entries made from 24 February. The 40 percent tariff on Brazilian goods went with them.
Section 232 was not before the Court and rests on a different statute. Proclamation 10976 took effect on 14 October 2025 and reaches softwood timber and lumber, wooden upholstered furniture, and kitchen cabinets and vanities. It is still in force.
Then on 22 July 2026 a Section 301 action placed 25 percent on most goods of Brazil, following an investigation the United States Trade Representative opened in July 2025 into digital trade, preferential tariffs, anti-corruption enforcement, intellectual property, ethanol market access and illegal deforestation. The notice says USTR will consider whether modifications are appropriate, so this is the regime most likely to move.
02The two regimes, and which one your product is in
Section 232 is narrow. It names fifteen subheadings of Chapter 44 for softwood timber and lumber, four tariff lines for wooden upholstered furniture, and three for completed kitchen cabinets and vanities and their parts. Everything else in Chapter 94 that touches those same lines sits at zero.
Section 301 is wide. It places 25 percent on most goods of Brazil under heading 9903.05.01, and it does not stack: goods subject to Section 232 are excluded from it. So a wooden-framed upholstered sofa pays the Section 232 rate and not the Brazil 25 on top of it. A dining table, a wardrobe, a rug, an outdoor lounger: outside the Section 232 list, inside the Brazil 25.
The January increase has already been postponed once, from 1 January 2026, and the proclamation exempts countries that reach an agreement with the United States before it bites. The United Kingdom already pays 10 percent on these furniture headings, and Japan and the European Union 15. Brazil has no such agreement. Treat the date as scheduled rather than settled, and confirm it before you commit to a price.
Scroll the table sideways to compare every column.
| What it covers | Heading | Now | From 1 Jan 2027 |
|---|---|---|---|
| Softwood timber and lumber, fifteen subheadings of Chapter 44 | 9903.76.01 | 10% | 10% |
| Wooden upholstered furniture: 9401.61.4011, 9401.61.4031, 9401.61.6011, 9401.61.6031 | 9903.76.02 | 25% | 30% |
| Completed kitchen cabinets and vanities and their parts: 9403.40.9060, 9403.60.8093, 9403.91.0080 | 9903.76.03 | 25% | 50% |
| The same Chapter 94 codes where the article is not a completed cabinet or vanity | 9903.76.04 | 0% | 0% |
| Most other goods of Brazil, Section 301 | 9903.05.01 | 25% | 25% |
03The question that decides your landed cost
A Chapter 94 article classified in one of those seven tariff lines, but which is not a completed cabinet or vanity, sits at heading 9903.76.04 and pays nothing under Section 232. Whether it is therefore subject to Section 232 for the purpose of the Brazil exclusion, and so escapes the 25 percent as well, is not answered by either notice. On the same piece, that reading is worth 25 points of landed cost.
Classification is a licensed customs broker reading your actual bill of materials. It is not a sourcing consultancy, and anyone who tells you otherwise is selling you a risk they will not carry. What a sourcing consultancy can do is make sure the question gets asked while the piece is still a drawing.
A frame material, a cabinet door, a seat construction: each of those decisions moves the classification. Each is cheap to change before tooling and expensive after.
04Four regimes that have nothing to do with tariffs
Upholstered seating
16 CFR Part 1640 has been in force since 25 June 2021. It adopts California Technical Bulletin 117-2013 and tests the smoulder resistance of four things: the cover fabric, the barrier material, the resilient filling and the decking.
Since 25 June 2022 every covered piece carries a permanent label reading, word for word, “Complies with U.S. CPSC requirements for upholstered furniture flammability.” Note what is not required. Section 14(a) of the Consumer Product Safety Act does not apply to this standard, so there is no General Certificate of Conformity to issue. The label is the certification, which is why it has to be right.
Indoor upholstered seating is in scope, including furniture for children. Mattresses, foundations, bedding and exercise furniture are out.
Clothing storage
16 CFR Part 1261 reaches free-standing units at least 27 inches high, weighing at least 30 pounds, with at least 3.2 cubic feet of storage: chests, dressers, armoires, bureaus. Testing is to ASTM F2057-23 for units manufactured after 1 September 2023, and includes placement on carpet, multiple open drawers, and a simulated 60-pound child.
Bookcases, entertainment units, dining and office furniture, jewellery armoires, under-bed drawers and built-ins are outside it. A Brazilian factory that has only ever sold domestically has very likely never tested to this standard, which is a question of capability rather than of willingness.
Composite wood
TSCA Title VI, at 40 CFR Part 770, has applied to finished goods since 1 June 2018. Measured by ASTM E1333-14, the limits are 0.05 ppm for hardwood plywood with a veneer or composite core, 0.09 for particleboard, 0.11 for medium-density fibreboard and 0.13 for thin MDF of 8 mm or less.
Only certified panel may be imported, certified by a third-party certifier that the Environmental Protection Agency recognises. A certifier approved by the California Air Resources Board qualifies only where the EPA has recognised it, which is a distinction that catches buyers who were given a CARB certificate and assumed it was enough.
Hardboard, oriented strand board, structural plywood and panels, structural composite lumber and finger-jointed lumber are exempt. For Brazilian casegoods this is usually a question about the panel mill behind the furniture factory, not about the furniture factory.
Timber legality
A Lacey Act plant and plant product declaration names the genus, the species, the country of harvest, the quantity and the value. Phase VII, from 1 December 2024, extended the requirement to the remaining plant-product tariff codes that are not entirely composite. The European equivalent is stricter and later: see the <a href="/guides/european-union/">Country Guide: European Union</a>.
For Brazilian solid wood this means the species on the invoice has to be the species in the piece, and that is a documentation chain reaching back to the sawmill. A false declaration is the importer's exposure, not the exporter's.
05Where this lands in a specification
None of the four regimes above is a shipping problem. Every one of them is settled upstream of the purchase order, in decisions a buyer usually makes without knowing they are making them.
A barrier material chosen for cost decides whether the sofa passes a smoulder test. A dresser three inches taller than the drawing moves it inside Part 1261. A panel supplier swapped during a price negotiation decides whether the formaldehyde certificate is the one the EPA recognises. A species name typed into an invoice by someone in an export department decides whether the Lacey Act declaration is true.
That is why a verification visit reads a bill of materials and not a brochure, and why the order of work matters more than the length of the checklist. By the time a container is on the water, every one of these decisions has already been made.
06What we do here, and what we do not
We are not customs brokers and we are not freight forwarders. We do not classify goods for entry, we do not file declarations, and we do not sign anything on an importer's behalf.
What we do is read a specification against the regimes above before it is signed, and tell you which decisions move your landed cost and which move your compliance exposure. Then we verify in the plant that the factory can hold what the specification says, and put the finding in writing.
We work for the buyer. No factory pays us, and we take no percentage of what you order.
07Sources
- Amendments to Adjusting Imports of Timber, Lumber, and Their Derivative Products, 9 January 2026
- CBP CSMS 66492057, Section 232 import duties on timber, lumber and their derivative products
- USTR Notice of Action on Brazil, Federal Register, 20 July 2026
- 40 CFR Part 770, Formaldehyde Standards for Composite Wood Products
- 16 CFR Part 1640, Standard for the Flammability of Upholstered Furniture, Federal Register, 9 April 2021
- APHIS, Lacey Act Phase VII implementation, 1 December 2024

Country Guide: United States
Start with the specification, not the shortlist.
Tell us what you are trying to buy. We will tell you which of these regimes it falls under and what that changes about where it can be made.